DIY Slatwood Bench

Make this simple slatwood bench- it's easier than you think!Making furniture is one of my favorite things. There's very little more empowering than imagining a piece of furniture and actually making it a reality with a little hard work. Not only is furniture making a great way to potentially save money, but it's a really practical way to put your creativity to work!

Recently my mom asked my dad if he would be able to find time to make her a bench she could use at the dining table for family feasts and also in their entryway. I said, "Ma! Why don't I make you that bench?" Girls know how to use power tools too! So we worked together to come up with this simple slatwood bench design in a slightly distressed ebony finish.

DIY slatwood bench with tapered legsDIY slatwood bench with tapered legsMaterials:
-3 1×3" boards* ($3.82 each for pine)
-1 1×4" boards* ($4.58 for pine)
-8 1×2" boards* ($2.48 each for pine)
-4 angled leg plates (like ) ($1.14 each + $5.50 shipping= approximately $10)
-4 tapered legs in 12"-16" length, depending on your desired height—I used  ($17.95 each for pine), but are less expensive ($5.38 each).
-8 -32 1.5" flat wood screws
-16 finishing nails (at least 1.5")
-Gorilla Glue
-wood filler
-wood stain or paint and primer
-120 & 220 grit sandpaper
-extra fine steel wool

Total Cost (including lumber, legs, and leg mounting plates): $68
Cost assumes the less expensive table legs and does not include screws, paint, glue, etc., because those are items I already had on hand, and you may too. Also, cost of lumber will be lower if you buy longer boards and cut them down to size.

Tools:
-miter saw
-power drill

-standard drill bits & drivers
-2 & 2 (not pictured in supplies)
– (not pictured)
-tape measure
-hammer
-rag or sponge
-optional: power sander

*The length of the boards is up to you, but I used 4' long boards.

DIY slatwood bench with tapered legsMake this simple slatwood bench- it's easier than you think!Step One: Use the miter saw to cut 45 degree angles on the ends of two 1×3 boards as shown above. Cut down the length of the 1x2s to match the inside length of the freshly cut 1x3s. It is very important that the 1x2s are perfectly cut to exactly match the inside length of the mitered 1x3s.

Step Two: Use an extra board to space out the planks as shown above, arranging the 1x2s in the middle, and the 1x3s on the ends. Use scrap wood to make sure the ends of the 1x2s are even.

Make this simple slatwood bench- it's easier than you think!Step Three: Measure the distance between the 1x3s and cut two pieces of the 1×4 to that length. These will be the support boards for the bench. Screw them to the previously spaced-out 1x2s, as shown above. I attached mine 6" from the ends of the 1x2s. Make sure to keep pressure on the board while drilling the pilot holes and screwing in the wood screws, or you might mess up the board spacing.

Step Four: Clamp the Kreg jig onto the ends of the attached board and drill 2 pocket holes which will be used to connect the 1x3s to the edge.

Tips for Making Pocket Holes: It's difficult to give specific instructions for what stop point to set your Kreg jig when drilling pilot holes, because there are variants involved, such as where the stop collar is placed on your drill bit, what length screws you are using, and the exact thickness of your wood. My suggestion is to practice with scrap pieces of wood to ensure you do not over-drill or under-drill for the pocket holes.

Make this simple slatwood bench- it's easier than you think!Step Five: Loosely clamp the 1x3s to the edge of the attached support boards. Use a scrap piece of wood to make sure the edge of the 1×2 boards perfectly line up with the inside of the mitered 1×3 edge. Once each end of the bench is perfectly even with the mitered 1x3s, tighten the clamps. If the ends do not match up evenly, you may need to trim the attached 1x2s with a table saw, or else shave a bit off the mitered 1×3 before attaching them.

Step Six: While the 1x3s are tightly clamped, screw the 1.5" Kreg screws into the support boards, attaching the 1x3s securely to the base of the bench.

Tips for clamping: When clamping soft wood like pine, use scrap pieces of wood as a buffer between the clamp and your finished piece, or the clamp will imprint the wood. 

DIY slatwood bench with tapered legsStep Seven: Measure the entire width of the bench base to find the length to cut the last of the 1x3s to create the mitered end caps. Cut more than you think you will need, then slowly, slowly trim a tiny bit more off the ends until you get the perfect dry fit.

Step Eight: Loosely fit a belt clamp around the entire bench top, preparing for fitting in the mitered end caps you cut in step seven. Soak the end grains of the wood with water and cover with some Gorilla Glue.

Make this simple slatwood bench- it's easier than you think!Step Nine: Fit the mitered end cap into place and completely tighten the belt clamp. The pressure from the clamp and the moisture in the wood will activate the Gorilla Glue, creating a strong bond. I added some finishing nails to be extra sure the wood won't pop out of place due to natural shrinking/growing that occurs with moisture changes in the environment.

Step Ten: Sand down the entire bench with 120 grit sandpaper to fix any unevenness in the seams. If you have extreme unevenness, you can fix it with 60 grit sandpaper and a power sander. Add wood filler to any small gaps in the seams and to cover the nails, which should be slightly recessed into the wood. (You can recess nails by tapping them with another nail.) When the wood filler has set up, sand down the entire bench again with 220 grit sandpaper.

Step Eleven: Stain or paint the bench to your desired finish. If you are painting, make sure to wet sand the primer with 400 grit sandpaper and water before painting. This will ensure a silky smooth finish. If you are staining, always sand down with 0000 grade steel wool after each coat of stain and also after the first coat of sealer, unless you are using wax as a sealer.

DIY slatwood bench with angled tapered legsStep Twelve: Attach the leg mounting plates to the support boards of the bench. I attached mine about an inch from the support board's edge, making sure to work around the screws that were already in place. Make sure the placement of the angled leg plates will direct the legs' angle to the outside corner of the bench. Then screw the legs into place until they are perfectly tight.

Make this simple slatwood bench- it's easier than you think!DIY slatwood bench with tapered legsThis bench works great as a coffee table, extra seating, or a place to put your house plants. It's such a simple piece of furniture with lots of style!

DIY slatwood bench with tapered legsI love how sleek the bench is, and while I like the way it looks in my modern home, it will fit right in with my mom's transitional-styled decor too! –

Credits // Author and Photography: Mandi Johnson. Photos edited with Stella and Valentine from the .

  • Hi, this question is about an old post that is not accepting comments, but i figured i’d try to get the detail anyway. The feather pendant is stunning. You mention it took 8 trims? If by chance you remember, is that to mean that it was 16 yards? and was the diameter of the lantern 12″?
    If you remember, it’d be of help, thanks.

  • I love the artwork above your sofa! Did you make that? If not, maybe you could! 🙂

  • Thanks Mandi for the great project idea. It looks great. We also carry cleats for Mid Century Modern legs which are used to attach our McCobb or Wegner style legs and are for either straight or angled installation. The cleats and legs can be found here

  • Wow great job this looks awesome! It could easily be from a high end retailer selling for a few hundred pounds (hi from the UK!). Going to show this to my husband as we keep talking about giving our living room a makeover. Thanks!

  • Love the pattern at the top…makes all the difference…the table is perfect..

    xo
    Hems
    agoldentulip.blogspot.com

  • I love the painting! Did you DIY it? If so I’d love to see a tutorial if you’re willing to share!

  • wow what a wonderful table this is brilliant xx your blog is fast becoming one of my favourites x

  • Isn’t it cool? I’m sure you could make something similar, but I wanted to support the artist who originally created it. It was a colab with Scout & Catalogue with Debbie Carlos. You can check it out here:

    -Mandi

  • Thanks! I didn’t DIY it— purchased it from the artist. It’s an oversize print of marbling done by Scout & Catalogue for Debbie Carlos’ poster shop: -Mandi

  • It’s a heart leafed philodendron. Super easy to take care of, because it still does well in low light with limited watering. I started with one plant and split it into over 5 pots that I have all throughout my house! -Mandi

  • Is that the Karlstad? I’m having major sectional envy right now, love everything about this room including the DIY

  • Hello Mandy! I love the tutorial 🙂 I have the same couch as the one in the background and I was wondering if you could tell me where you got the legs for the couch? Thank you!!!

  • Mandi,
    BEAUTIFUL JOB! Can I ask about the finish – what kind of paint/stain did you use?

  • I want to make a bench like that! I have this beautiful rustic dining room table (Made of solid Pine) and I think it would be great to fit a few extra bods into the table with a bench. I think I’m gonna have to try this… Although, I don’t have any power tools.

  • I desperately want to make a coffee table similar to this shape but this is a bit above my skill level/price range and I don’t have an outdoor space to make it. Is there a simple way to attach these legs to a giant hunk of wood that you would recommend?

  • Yes it is! We saved $100 a month until we could walk into Ikea and buy it with cash. SO worth it! Someday I’d like a nicer sofa, but for now, this meets our needs perfectly. -Mandi

  • I got them from an Etsy shop called Uncle Bob’s Workshop, but last I checked they were taking a break from selling. I would just search online or on Etsy for “karlstad legs.” -Mandi

  • I borrowed my Dad’s drill for years before I was able to get this one for just $10, after a mail-in-rebate! It’s not the best, but so cheap! And I got my drill bits for Christmas last year. I still borrow the miter saw from my dad, but I’m hoping to get one of my own for Christmas this year. 🙂 -Mandi

  • Yeah! You could get a slab of wood, just make sure you strengthen it somehow, because I don’t think just one piece would be sturdy enough. It would probably bend. You could tack on 1x2s across the bottom of the edges to trim it out or something. Those leg plates I linked to above are the easiest things ot use as far as attaching legs go. You definitely need something like that. -Mandi

  • Love this so much! I’ve been dying for a slatted bench for awhile now and missed out on one at an antique shop. I never thought about making one myself, but that’s totally doable!!

    xo
    Christa

  • So how has it held up? Have you had any problems – weakness, wobbliness, etc – from the angle plates? Is it strong enough for someone to sit on? How much weight do you think?

This site uses Akismet to reduce spam. .